CH340T CHIP DRIVER

Yep – certainly am! Any comments on doing this, please? Prior to shorting it the UNO clone ran everything my genuine UNO ran so there were no problems with it prior to this event! This red text always ends with the above “avrdude” statement when the program compiles OK – or a cryptic explanation of any problem areas encountered in this program, should this occur?? I have read about “software fuses?? Is either or both of these a good or bad idea – could doing either or both kill my good chip??? What sketch have you tried – “Blink” using the on-board LED?

Uploader: Vushicage
Date Added: 4 January 2005
File Size: 9.33 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 70250
Price: Free* [*Free Regsitration Required]

It has little or nothing to do with whether it is a clone or not. Have you tried the loopback test in the installation section? Does it tell you “Done Uploading”?

Arduino UNO Clone CHT Chip

One final comment – the whole time I was typing this question all of the text decenders were missing; that is until just now when I started writing this comment? Will do shortly, and thanks for your cotinuing help! Does the Uno appear to run the last sketch you loaded onto it? This red text seems to correspond to a line of each step in the running program – there are and always have been a multitude of red text lines all showing numbers in []’s for each and every program run!

CH340 Drivers for Windows, Mac and Linux

This is about the limit of my abilities at this stage but I have two questions: Conclusion is that this clone chip is therefore UTS! Hope this gives you the missing data? I chil checked all of the lines on the clone and all pins are showing their correct voltages.

  M AUDIO 1X1 UNO DRIVER DOWNLOAD

Looking forward to your comments. Anyway appreciate any help on this possible programming matter, please. Looking forward to your continuing help.

I can load the blink program and it gives the ‘AVRdude done – thanks’ note but the LED on 13 does not illuminate or respond to this program?? Prior to shorting it the UNO clone ran everything my genuine UNO ran so there were no problems with it prior to this event! I have also noticed a number of other cjip having different alpha characters after the and would like to know if any of these will substutute for my original P-PU chip assuming the same frequency; in particular I can get P locally off the shelf but not P-PU??

Yep – certainly am! Any plans for the genuine article to incorporate this functionality – I believe it would increase UNO sales tremendously, if it was??? What does “it goes through the motions of loading a sketch” mean?

All very mysterious – either no one really looks at these comments in the box under the ch340y box or I have something uniquely totally weird going on and I am the only person in the world this is happening too??? I have read about “software fuses?? Ch340f are not the first person to comment as you have when I have mentioned this “happening” in previous posts??? Any comments on doing this, please? Hey fella, we are going to need a lot more accurate information than that to get any idea of the situation.

  ECS P4VMM2 1.0 AUDIO DRIVER DOWNLOAD

This red text always ends with the above “avrdude” statement when the program compiles OK ch340r or a cryptic explanation of any problem areas encountered in this program, should this occur?? If you were critically close to the bottom of the text box, some systems OS might behave oddly.

CH Drivers for Windows, Mac and Linux

By the way please remember I am a total newby to programming chips etc – so I would greatly appreciate not using and techie jargon in any reply. If they carry the same or similar “fuse” functionality how would I go about reprograming same??

Somehow I rather think this latter possibility is a totally implausable one?? Thanks guys for your replies: I am simply amazed by your comment you have never seen cnip words???

And if so, how should I go about this? I don’t know if the clone has short protection as the ligit UNOs do but from this it cgip appear not? What sketch have you tried – “Blink” using the on-board LED? Is either or both of these a good or bad idea – could doing either or both kill my good chip???